Cyberbond接着剂中文技术网站 - Your Source for Industrial Adhesive -- Apollo阿波罗瞬间接着剂,Cyberlite

CYBERCRYL™ 1326 - Acrylic Adhesive
快速型平面结构胶 - 高强度金属接着

Cybercryl平面架构用接着剂为Acrylic base之接着剂, 使用于平面之接着, 由于强度非常高, 因此常被使用于作架构性之接着组装. 专门针对金属、陶瓷、玻璃等接着，具有较高之耐冲击、耐压力及耐震动。可手动或自动化点胶，初步固化速度快, 可节省时间降低装配成本。 Cybercryl 1326 快速固定型接着剂 - 快速固化特性, 适合生产线之快速组装量产. - 不用混合(非混合型) - 不含溶剂,低气味 - 高流变性, 低垂流, 可于垂直面施胶 - 产品搭配活化剂使用时, 初步固定时间最快可低于15秒. - 固化后具有高韧性及耐冲击之特性, - 使用于金属,玻璃及陶瓷之架构性强力接合, 例如硅钢片, 铝, 钢板 - 玻璃艺品及电子零件等. - 容易操作, 可搭配设计为自动化生产线
Cyberbond CYBERCRYL 1326 is a medium-viscosity, fast cure adhesive system which gives good tensile shear strength for glass, metals and ceramics. CYBERCRYL 1326 has good toughness where thermal cycling forces produce expansion stresses. CYBERCRYL 1326 is a fast curing product when used with Activator 1094 and fixtures in 15 seconds at 23oC. Recommended for glass, ferrite bonding, magnet materials and other ceramic type substrates to metals or to each other.
Product Information:

	Appearance :	Amber	产品技术数据 Data Sheet (Cybercryl 1326)
	Viscosity (cps @ 68F) :	12,000 cP	产品技术数据 Data Sheet (Cybercryl 1094)
	Service Temperature Range :	-65F to 325F	物质安全数据表 MSDS (Cybercryl 1326)
	Tensile Shear Strength:	>3500 psi on aluminum	物质安全数据表 MSDS (Cybercryl 1094)
	Substrates to bond:	铝, 铝合金, 铁, 不锈钢, 铜, 钨钢, 镍, 玻璃, 锌, 陶瓷...等.	使用说明书 Useful hint (Chinese version)
			Inquire to us

Cybercryl 1326 使用方式: Instructions For Use
一般操作模式: 1. 将活化剂Cybercryl 1094涂于预接合部位(约1~5秒自动挥发干). 2. 另一面涂上Cybercryl 1326并接合两材质, 轻压至材质固定(约15~30秒). 加热模式: Cybercryl 1326可以用加热模式固化, 以200oF(约95oC) 半小时可达完全固化, 若以更高之温度可缩短所需要加热之时间.
Typical Process Methods - Cybercryl 1326 Activator: Apply adhesive as a bead or in drops to ensure enough material is applied for filling the bond-line with a small amount of squeeze out. Apply Activator to the other mating bonding surface in a thin film using the applicator brush or with another applicator. Assemble the parts and fixture with light clamp pressure for a minimum of 10 seconds where good contact of parts is evident. Larger gaps will take longer to fixture and reach full cure strength. For gaps over 0.020§, use Activator on both parts and apply adhesive over one activator primed surface, being careful not to touch adhesive applicator to the other primed surface. Heat Cure: Cure at 200F for 1/2 hour bond-line temperature, higher temperatures will produce faster cures.